Harris Spain Harris Germany Harris Italy Harris U.S.A.
The Harris Products Group  
EQUIPMENT
Machine Cutting Tips

  VVC Plated Shell
VVCU Unplated Shell

  • Minimizes kerf
  • Increased cutting speeds, reduces heat input
  • High quality machine cuts, reduces afterwork
  • Used with low cost fuel gases

6290-VVC High Speed Oxy- Propane/Natural Gas Cutting Tip Chart-Plated Shell (.088” Cup Depth)
PART
 NO.		 TIP
SIZE		 PLATE
THICK.
INCHES		 CUTT.
SPEED
I.P.M.		 CUTTING
OXYGEN
PSIG		 PREHEAT
OXYGEN
PSIG
HIGH		 PREHEAT
OXYGEN
PSIG
LOW		 PREHEAT
FUEL
PSIG		 CUTTING
OXYGEN
CONSUMP.
SCFH		 LOW PREHEAT
OXYGEN
CONSUMP.
SCFH		 PROPANE
CONSUMP.
SCFH		 NAT. GAS
CONSUMP.
SCFH		 KERF IN.
1501310
5/0
3/16
20
40
15
8
4 oz.-2
15
30
6
15
.05
1501320
4/0
1/4
20
50
15
10
4 oz.-2
40
35
7
18
.06
1501330
3/0
3/8
18
75
35
10
4 oz.-2
80
35
7
18
.07
1501340
2/0
1/2
18
75
35
10
4 oz.-2
90
35
7
18
.07
1501350
0
3/4
15
90
35
10
4 oz.-2
125
35
7
18
.08
1501360
0 1/2
1 1/4
14
100
35
12
4 oz.-2
170
40
8
20
.08
1501370
1
2
13
100
35
12
4 oz.-2
200
40
8
20
.09
1501380
1 1/2
3
9
100
35
12
4 oz.-2
250
40
8
20
.11
1501390
2
4
7
100
35
12
4 oz.-2
325
40
8
20
.12
1501400
2 1/2
5
6
100
35
12
4 oz.-2
395
40
8
20
.13
1501410
3
6
5
100
40
12
4 oz.-2
425
40
8
20
.14
1501420
4
8
5
100
40
12
4 oz.-2
525
40
8
20
.16
1501430
5
9
4
90
40
-
4 oz.-2
580
100
20
50
.20
1501440
5 1/2
10
4
90
40
-
4 oz.-2
600
100
20
50
.25
1501120
5NH*
10
4
60
40
-
4 oz.-2
600
100
20
50
.25
1501130
6NH*
11
4
60
40
-
4 oz.-2
690
100
20
50
.25
1501140
7NH*
12
4
60
40
-
4 oz.-2
825
100
20
50
.25
1501190
8NH*
15
3
60
40
-
4 oz.-2
925
100
20
50
.30
Note: NH Tips are not plated

6290-VVCU High Speed Oxy- Propane/Natural Gas Cutting Tip Chart-Unplated Shell (.062” Cup Depth)
PART
 NO.		 TIP
SIZE		 PLATE
THICK.
INCHES		 CUTT.
SPEED
I.P.M.		 CUTTING
OXYGEN
PSIG		 PREHEAT
OXYGEN
PSIG
HIGH		 PREHEAT
OXYGEN
PSIG
LOW		 PREHEAT
FUEL
PSIG		 CUTTING
OXYGEN
CONSUMP.
SCFH		 LOW PREHEAT
OXYGEN
CONSUMP.
SCFH		 PROPANE
CONSUMP.
SCFH		 NAT. GAS
CONSUMP.
SCFH		 KERF IN.
1502120
5/0
3/16
20
40
15
8
4 oz.-2
15
30
6
15
.05
1502121
4/0
1/4
20
50
15
10
4 oz.-2
40
35
7
18
.06
1502122
3/0
3/8
18
75
35
10
4 oz.-2
80
35
7
18
.07
1502123
2/0
1/2
18
75
35
10
4 oz.-2
90
35
7
18
.07
1502124
0
3/4
15
90
35
10
4 oz.-2
125
35
7
18
.08
1502125
0 1/2
1 1/4
14
100
35
12
4 oz.-2
170
40
8
20
.08
1502126
1
2
13
100
35
12
4 oz.-2
200
40
8
20
.09
1502127
1 1/2
3
9
100
35
12
4 oz.-2
250
40
8
20
.11
1502128
2
4
7
100
35
12
4 oz.-2
325
40
8
20
.12
1502129
2 1/2
5
6
100
35
12
4 oz.-2
395
40
8
20
.13
1502130
3
6
5
100
40
12
4 oz.-2
425
40
8
20
.14
1502131
4
8
5
100
40
12
4 oz.-2
525
40
8
20
.16
1502132
5
9
4
90
40
-
4 oz.-2
580
100
20
50
.20


NOTES:

  1. Use next size larger tip with same pressure for contour cutting.
  2. Use highly carburizing preheat flame for light plate cutting.
  3. Cutting oxygen pressure should be measured at top of torch.

CLEANING INSTRUCTIONS: The wire brush included with tip cleaner E-9 (P/N 9000160) should be used for cleaning preheat slots and for removing spatter from the tip face. When cleaning the preheat slots, do not brush across the slots as this motion can damage the slots. Always brush along the length of the slot to remove dirt or spatter.


E-9 TIP 
Two Piece Cleaners
P/N: 9000160
The Harris Products Group 4501 Quality Place Mason, OH 45040-1971 800.733.4043
Copyright ©2008, HarrisProductsGroup.com. All Rights Reserved.