Harris Spain Harris Germany Harris Italy Harris U.S.A.
The Harris Products Group  
EQUIPMENT
Machine Cutting Tips

  VVCM Unplated Shell
VVCP Unplated Shell

  • Minimizes kerf
  • Increased cutting speeds, reduces heat input
  • High quality machine cuts, reduces afterwork
  • Used with low cost fuel gases

 
6290-VVCM High Speed Oxy- MAPP® Cutting Tip Chart-Unplated Shell (.010 Cup Depth)
PART
 NO.		 TIP
SIZE		 PLATE
THICK.
INCHES		 CUTT.
SPEED
I.P.M.		 CUTTING
OXYGEN
PSIG		 PREHEAT
OXYGEN
PSIG
HIGH		 PREHEAT
OXYGEN
PSIG
LOW		 PREHEAT
FUEL
PSIG		 CUTTING
OXYGEN
CONSUMP.
SCFH		 LOW PREHEAT
OXYGEN
CONSUMP.
SCFH		 MAPP®
CONSUMP.
SCFH		 KERF IN.
1501620
5/0
3/16
20
40
15
8
4 oz.-2
15
30
6
.05
1501630
4/0
1/4
20
50
15
10
4 oz.-2
40
35
7
.06
1501640
3/0
3/8
18
75
35
10
4 oz.-2
80
35
7
.07
1501650
2/0
1/2
18
75
35
10
4 oz.-2
90
35
7
.07
1501660
0
3/4
15
90
35
10
4 oz.-2
125
35
7
.08
1501670
0 1/2
1 1/4
14
100
35
12
4 oz.-2
170
40
8
.08
1501680
1
2
13
100
35
12
4 oz.-2
200
40
8
.09
1501690
1 1/2
3
9
100
35
12
4 oz.-2
250
40
8
.11
1501700
2
4
7
100
35
12
4 oz.-2
325
40
8
.12
1501710
2 1/2
5
6
100
35
12
4 oz.-2
395
40
8
.13
1501720
3
6
5
100
40
12
4 oz.-2
425
40
8
.14
1501730
4
8
5
100
40
12
4 oz.-2
525
40
8
.16
1501740
5
9
4
90
40
-
4 oz.-2
580
100
20
.20

 6290-VVCP High Speed Oxy- Propylene Cutting Tip Chart-Unplated Shell (.034 Cup Depth)
PART
 NO.		 TIP
SIZE		 PLATE
THICK.
INCHES		 CUTT.
SPEED
I.P.M.		 CUTTING
OXYGEN
PSIG		 PREHEAT
OXYGEN
PSIG
HIGH		 PREHEAT
OXYGEN
PSIG
LOW		 PREHEAT
FUEL
PSIG		 CUTTING
OXYGEN
CONSUMP.
SCFH		 LOW PREHEAT
OXYGEN
CONSUMP.
SCFH		 PROPYLENE
CONSUMP.
SCFH		 KERF IN.
1502200
5/0
3/16
20
40
12
8
2
15
32
13
.05
1502202
4/0
1/4
20
50
12
8
2
40
32
13
.06
1502204
3/0
3/8
18
75
25
8
2
80
32
13
.07
1502206
2/0
1/2
18
75
25
8
2
90
32
13
.07
1502208
0
3/4
15
90
25
8
2
125
32
13
.08
1502210
0 1/2
1 1/4
14
100
25
8
2
170
32
13
.08
1502212
1
2
13
100
25
10
2
200
40
16
.09
1502214
1 1/2
3
9
100
25
10
2
250
40
16
.11
1502216
2
4
7
100
25
10
2
325
40
16
.12
1502218
2 1/2
5
6
100
30
10
2
395
40
16
.13
1502220
3
6
5
100
30
10
2
425
40
16
.14
1502222
4
8
5
100
30
10
2
525
40
16
.16
1502224
5
9
4
90
30
10
2
580
40
16
.20


NOTES:

  1. Use next size larger tip with same pressure for contour cutting.
  2. Use highly carburizing preheat flame for light plate cutting.
  3. Cutting oxygen pressure should be measured at top of torch.

CLEANING INSTRUCTIONS: The wire brush included with tip cleaner E-9 (P/N 9000160) should be used for cleaning preheat slots and for removing spatter from the tip face. When cleaning the preheat slots, do not brush across the slots as this motion can damage the slots. Always brush along the length of the slot to remove dirt or spatter.

 

E-9 TIP 
Two Piece Cleaners
P/N: 9000160
The Harris Products Group 4501 Quality Place Mason, OH 45040-1971 800.733.4043
Copyright ©2008, HarrisProductsGroup.com. All Rights Reserved.